Rubber-lined waterway
Synthetic rubber lining for firefighting water delivery.
Product photograph shows a representative hose assembly. Confirm the diameter, length, coupling and operating rating with your quotation.
FROZENFIRE · RRL HOSES RANGE
Rubber Braided Hose Type-B
Rubber-lined construction for industrial duty.
A heavy-duty Type B fire hose with a woven polyester jacket and synthetic rubber lining for industrial and municipal firefighting applications. The catalogue’s technical table specifies a three-layered synthetic rubber lining.
Type B · Rubber linedWoven polyester jacketSynthetic rubber lining
Discuss your requirement +91 7878 717 818- Working pressure
- Up to 16–20 barCatalogue value; confirm the selected rating
- Burst pressure
- Up to 42 barBurst rating, not a working-pressure limit
- Standard sizes
- 6 sizes38, 50, 63, 70, 75, 100 mm
- Standard lengths
- 4 lengths7.5, 15, 20, 30 m
PRODUCT OVERVIEW
A reinforced hose for industrial installations.
The Type B hose combines a high-tenacity polyester jacket with a synthetic rubber inner tube. The catalogue identifies the lining as three-layered synthetic rubber and describes use in permanent fire protection installations and emergency systems.
Select the hose diameter, length and coupling configuration together with the required working pressure. Final suitability depends on the selected hose assembly and installation conditions.
Woven jacket
High-tenacity polyester reinforcement around the inner tube.
Industrial applications
Catalogue applications include hydrant systems, plants and municipal services.
Coupling options
Stainless steel, gunmetal and aluminium options are listed for the range.
TECHNICAL SPECIFICATIONS
Size. Pressure.
Construction.
Typical hose specifications from the Frozenfire catalogue, revision 07/2026.
Download technical catalogue| Parameter | Specification |
|---|---|
| Hose type | Type B |
| Construction | Rubber lined |
| Jacket material | Polyester |
| Inner lining | Three-layered synthetic rubber |
| Hose standard / marking | IS 636 · ISI mark stated in the catalogue |
| Standard sizes | 38, 50, 63, 70, 75, 100 mm |
| Standard lengths | 7.5, 15, 20, 30 m |
| Working pressure | Up to 16–20 bar |
| Burst pressure | Up to 42 bar |
| Temperature range | −30°C to +90°C |
| Coupling materials | Stainless steel / Gunmetal / Aluminium |
| Coupling standard / marking | IS 903 · ISI mark stated in the catalogue |
The catalogue gives typical specifications and “up to” pressure values. Confirm the working-pressure rating for the selected hose size and coupled assembly. Burst pressure is not the permitted operating pressure.
CONSTRUCTION & OPTIONS
Woven reinforcement. Synthetic rubber lining.
High-tenacity woven polyester reinforces the hose around a three-layered synthetic rubber lining.
| Parameter | Specification |
|---|---|
| Jacket reinforcement | High-tenacity polyester |
| Inner lining | Three-layered synthetic rubber |
| Outer jacket | Woven polyester |
| Coupling material options | Stainless steel / Gunmetal / Aluminium |
Photographs show a representative hose and coupling configuration. Confirm the selected construction, coupling material and connection details with your quotation.
APPLICATIONS
Where the hose fits.
Application areas listed for this hose in the catalogue. Confirm the selected assembly for the required service and installation conditions.
- 01Oil & gas facilities
- 02Petrochemical & chemical plants
- 03Steel plants
- 04Thermal power stations
- 05Airports & marine installations
- 06Fire vehicles
- 07Industrial fire hydrant systems
- 08Municipal fire services
CONNECTION & USE
Connect. Deploy.
Recover.
Catalogue guidance for hose handling. Follow the instructions for the selected assembly and the installed firefighting equipment.
Inspect and connect
Inspect the hose and couplings before use. Connect securely to the hydrant valve, monitor or pump outlet and check that the couplings are properly locked.
Deploy and supply
Straighten the hose to prevent kinking and open the water supply gradually to avoid water hammer. Use the connected branch pipe or nozzle according to its instructions and the site procedure.
Drain and store
After use, close the water supply slowly, drain the hose completely, and clean and dry it before rolling and storage.
INSPECTION & MAINTENANCE
Keep the hose
ready for service.
Inspect the hose after each use and maintain the couplings, gaskets and locking mechanisms as part of the equipment maintenance programme.
01Inspection and fittings
- Inspect after each use for cuts, abrasion, punctures or other damage.
- Check couplings, gaskets and locking mechanisms regularly.
- Replace damaged hoses or couplings before returning the assembly to service.
02Cleaning and storage
- Wash with clean water after use, especially after exposure to chemicals, saltwater or foam concentrate.
- Dry completely before rolling and storing.
- Store in a cool, dry, well-ventilated place away from direct sunlight.
03Handling and periodic checks
- Avoid dragging the hose over sharp edges or rough surfaces.
- Carry out periodic hydrostatic pressure testing in accordance with the applicable standard and the selected hose rating.
- Confirm the relevant test procedure and pressure before testing the assembly.
DOCUMENTS & SUPPORT
Keep the hose details close.
Download the original Fire Hose Pipe catalogue for Type A, Type II and Type B, or request documents for your selected hose assembly.
Fire Hose Pipe catalogue
Original Frozenfire range document
Product descriptions, construction, typical specifications, applications, operating guidance and maintenance information.
Download catalogueYour selected configuration
Project documentation
Confirm the hose type, diameter, length, pressure rating, coupling material and connection details for the required assembly.
Request technical detailsDISCUSS YOUR REQUIREMENT
Specify the hose
for your project.
Share the hose type, diameter, length and quantity. Our team can review the operating requirement, coupling arrangement and product documentation.
Request a quotationFor a useful quotation
- 01Hose type, diameter and length
- 02Required working pressure and intended service
- 03Coupling material and connection details
- 04Quantity and delivery location
- 05Required marking, inspection and product documentation
Domestic supply & export
+91 7878 717 818