Bonded construction
Permanent adhesion between the elastomeric lining and the jacket.
Product photograph shows a representative hose assembly. Confirm the diameter, length, coupling and operating rating with your quotation.
FROZENFIRE · RRL HOSES RANGE
Elastomeric Hose Type-II
Bonded lining. Flexible water delivery.
An elastomeric-lined fire hose with a circular-woven polyester jacket and permanently bonded thermoplastic elastomer lining. The catalogue describes a flexible construction with resistance to abrasion, ozone and weathering for firefighting water delivery.
Type II · ElastomericPermanently bonded liningPolyester jacket
Discuss your requirement +91 7878 717 818- Working pressure
- Up to 16 barCatalogue value; confirm the selected rating
- Burst pressure
- Up to 34 barBurst rating, not a working-pressure limit
- Standard sizes
- 6 sizes38, 50, 63, 70, 75, 100 mm
- Standard lengths
- 4 lengths7.5, 15, 20, 30 m
PRODUCT OVERVIEW
A bonded lining. A flexible assembly.
The Type II hose uses a seamless elastomeric lining permanently bonded to a woven polyester jacket. The technical table identifies the lining as thermoplastic elastomer.
The catalogue describes low-friction water delivery and resistance to abrasion, ozone, UV and ageing. Confirm the selected size, coupling arrangement and operating rating for the installation.
Flexible deployment
A flexible, lightweight arrangement for handling and storage.
Water delivery
An elastomeric lining designed to support low-friction hydraulic flow.
Surface resistance
Catalogue-described resistance to abrasion, ozone and weathering.
TECHNICAL SPECIFICATIONS
Size. Pressure.
Construction.
Typical hose specifications from the Frozenfire catalogue, revision 07/2026.
Download technical catalogue| Parameter | Specification |
|---|---|
| Hose type | Type II |
| Construction | Elastomeric lined |
| Jacket material | Polyester |
| Inner lining | Thermoplastic elastomer |
| Hose standard / marking | IS 636 · ISI mark stated in the catalogue |
| Standard sizes | 38, 50, 63, 70, 75, 100 mm |
| Standard lengths | 7.5, 15, 20, 30 m |
| Working pressure | Up to 16 bar |
| Burst pressure | Up to 34 bar |
| Temperature range | −20°C to +80°C |
| Coupling materials | Stainless steel / Gunmetal / Aluminium |
| Coupling standard / marking | IS 903 · ISI mark stated in the catalogue |
The catalogue gives typical specifications and “up to” pressure values. Confirm the working-pressure rating for the selected hose size and coupled assembly. Burst pressure is not the permitted operating pressure.
CONSTRUCTION & OPTIONS
Polyester jacket. Bonded elastomeric lining.
The elastomeric lining is permanently bonded to a circular-woven polyester jacket with an abrasion-resistant outer surface.
| Parameter | Specification |
|---|---|
| Jacket | Circular-woven polyester |
| Inner lining | Thermoplastic elastomer |
| Bonding | Permanent adhesion |
| Outer surface | Abrasion resistant |
| Coupling material options | Stainless steel / Gunmetal / Aluminium |
Photographs show a representative hose and coupling configuration. Confirm the selected construction, coupling material and connection details with your quotation.
APPLICATIONS
Where the hose fits.
Application areas listed for this hose in the catalogue. Confirm the selected assembly for the required service and installation conditions.
- 01Municipal fire brigades
- 02Industrial fire systems
- 03Refineries & petrochemical plants
- 04Airports
- 05Fire vehicles
- 06Commercial buildings
- 07Marine fire protection
CONNECTION & USE
Connect. Deploy.
Recover.
Catalogue guidance for hose handling. Follow the instructions for the selected assembly and the installed firefighting equipment.
Inspect and connect
Inspect the hose and couplings before use. Connect securely to the hydrant valve, monitor or pump outlet and check that the couplings are properly locked.
Deploy and supply
Straighten the hose to prevent kinking and open the water supply gradually to avoid water hammer. Use the connected branch pipe or nozzle according to its instructions and the site procedure.
Drain and store
After use, close the water supply slowly, drain the hose completely, and clean and dry it before rolling and storage.
INSPECTION & MAINTENANCE
Keep the hose
ready for service.
Inspect the hose after each use and maintain the couplings, gaskets and locking mechanisms as part of the equipment maintenance programme.
01Inspection and fittings
- Inspect after each use for cuts, abrasion, punctures or other damage.
- Check couplings, gaskets and locking mechanisms regularly.
- Replace damaged hoses or couplings before returning the assembly to service.
02Cleaning and storage
- Wash with clean water after use, especially after exposure to chemicals, saltwater or foam concentrate.
- Dry completely before rolling and storing.
- Store in a cool, dry, well-ventilated place away from direct sunlight.
03Handling and periodic checks
- Avoid dragging the hose over sharp edges or rough surfaces.
- Carry out periodic hydrostatic pressure testing in accordance with the applicable standard and the selected hose rating.
- Confirm the relevant test procedure and pressure before testing the assembly.
DOCUMENTS & SUPPORT
Keep the hose details close.
Download the original Fire Hose Pipe catalogue for Type A, Type II and Type B, or request documents for your selected hose assembly.
Fire Hose Pipe catalogue
Original Frozenfire range document
Product descriptions, construction, typical specifications, applications, operating guidance and maintenance information.
Download catalogueYour selected configuration
Project documentation
Confirm the hose type, diameter, length, pressure rating, coupling material and connection details for the required assembly.
Request technical detailsDISCUSS YOUR REQUIREMENT
Specify the hose
for your project.
Share the hose type, diameter, length and quantity. Our team can review the operating requirement, coupling arrangement and product documentation.
Request a quotationFor a useful quotation
- 01Hose type, diameter and length
- 02Required working pressure and intended service
- 03Coupling material and connection details
- 04Quantity and delivery location
- 05Required marking, inspection and product documentation
Domestic supply & export
+91 7878 717 818